The term hipot is usually used as an abbreviation for high potential. It is a term that is used to refer to a certain class of electrical safety testing instruments referred to as a hipot tester. These instruments are used in the verification of the electrical insulation in finished cables, appliances, and other wired assemblies. Such assemblies include electric motors, transformers, and printed circuit boards just to mention a few.
Upon the manufacture or assembly of an appliance or product, it is usual for some degree of electrical leakage to occur. However, the leakage is usually very low and is brought about by internal capacitance and voltages inside the appliance. It is normal for such leakage to occur and it needs to be expected of every device. There exist a number of instances where the leakage, for some reason, may be excess.
Faults in the design or disintegration of product insulation among many other reasons may be the cause of the excessive leakage. These flaws often cause excessive leaking of current and may give rise to electrical shock for any individual that comes into contact with the defective appliance. The essence of a hipot test is to ensure and verify that the product has enough insulation so that the user of the device may not be electrocuted.
Dielectric Withstanding Voltage (DWV) is another term used in place of the term hipot test. This process involves application of a high voltage between the earth ground shielding and the conductor in the product that carry current. Exposure to excessive voltage causes resultant current flow through the product. A high potential tester is the gadget used in monitoring of this resultant current, which is also called leakage current.
One major assumption is made in hipot testing. The assumption is that by applying excessive voltage, the insulation of the product should break, and if it does not, then the device should work fine under normal conditions. The appliance is supposed to be resilient against normal voltage, which is often applied in ordinary everyday use of most devices. It is this assumption that gives rise to the name Dielectric Withstanding Voltage.
The aim of the test is to stress the insulation used in the product. However, besides stressing the insulation, the test is also used to detect defects in workmanship. The most important aspects of workmanship that are monitored are the small gap spacings that occur between current-carrying conductors and earth ground. Under normal operating environment, these small gaps can be closed by contaminants, shock, vibration, humidity, and dirt.
When the gaps are closed, current is allowed to flow. Such conditions can be a major electrical hazard that must be corrected at the factory before the product is released into the market. Such defects cannot be detected by any other method besides DWV. Even though other methods may be used to attempt to resolve these problems, but they cannot be as effective as DWV.
An electric device that manufacturers use in verification of electrical insulation is a high potential tester. It is made of a source of high voltage, a switching matrix and a current meter. Connection of the source of voltage and the current meter is done by the matrix switch. Including a display and a microcontroller automates the process of testing.
Upon the manufacture or assembly of an appliance or product, it is usual for some degree of electrical leakage to occur. However, the leakage is usually very low and is brought about by internal capacitance and voltages inside the appliance. It is normal for such leakage to occur and it needs to be expected of every device. There exist a number of instances where the leakage, for some reason, may be excess.
Faults in the design or disintegration of product insulation among many other reasons may be the cause of the excessive leakage. These flaws often cause excessive leaking of current and may give rise to electrical shock for any individual that comes into contact with the defective appliance. The essence of a hipot test is to ensure and verify that the product has enough insulation so that the user of the device may not be electrocuted.
Dielectric Withstanding Voltage (DWV) is another term used in place of the term hipot test. This process involves application of a high voltage between the earth ground shielding and the conductor in the product that carry current. Exposure to excessive voltage causes resultant current flow through the product. A high potential tester is the gadget used in monitoring of this resultant current, which is also called leakage current.
One major assumption is made in hipot testing. The assumption is that by applying excessive voltage, the insulation of the product should break, and if it does not, then the device should work fine under normal conditions. The appliance is supposed to be resilient against normal voltage, which is often applied in ordinary everyday use of most devices. It is this assumption that gives rise to the name Dielectric Withstanding Voltage.
The aim of the test is to stress the insulation used in the product. However, besides stressing the insulation, the test is also used to detect defects in workmanship. The most important aspects of workmanship that are monitored are the small gap spacings that occur between current-carrying conductors and earth ground. Under normal operating environment, these small gaps can be closed by contaminants, shock, vibration, humidity, and dirt.
When the gaps are closed, current is allowed to flow. Such conditions can be a major electrical hazard that must be corrected at the factory before the product is released into the market. Such defects cannot be detected by any other method besides DWV. Even though other methods may be used to attempt to resolve these problems, but they cannot be as effective as DWV.
An electric device that manufacturers use in verification of electrical insulation is a high potential tester. It is made of a source of high voltage, a switching matrix and a current meter. Connection of the source of voltage and the current meter is done by the matrix switch. Including a display and a microcontroller automates the process of testing.
About the Author:
We have all the detailed specifications on hipot tester the best on our related homepage. Simply use this link to reach the main website at http://www.rossengineeringcorp.com/products/measurement/ac-dc-digital-hipots.html.
Keine Kommentare:
Kommentar veröffentlichen